- Short wavelength laser based detection
- Advanced detection technology equivalent to hundreds of thousands of sensors
- Clean air barrier for optics protection
- Most robust contamination resistance
- Backward compatible with VESDA VLP
The VEU series of aspirating smoke detectors are the premium detector of the VESDA-E range. An Ultra-wide sensitivity range; 15 times greater than VESDA VLP, and provision for more sampling holes provide an increased coverage in high airflow applications by up to 40%. Considerably longer linear pipe runs and extended branched pipe network configurations cater perfectly to applications with higher ceilings providing an increased coverage by up to 80% whilst allowing convenient detector mounting for ease of service and maintenance. A range of revolutionary new features provide unsurpassed detection performance, flexibility, field programmability, connectivity and reduced total cost of ownership.
Installation, Commissioning and Operation
VEU features a robust IP40-rated enclosure and is equipped with a powerful aspirator that provides a total pipe length of 800m (2,624ft). It is fully supported by the ASPIRE-E and Xtralis VSC software applications which facilitate ease of pipe network design, system commissioning and maintenance together with compatibility with existing VESDA installations.
Colour Touch Screen Display
The VEU-A10 detector features a 3.5” colour touch screen display which provides a range of status information including smoke level as well as trouble conditions. A simple navigation system allows the user to view all the status information.
VESDA devices communicate on VESDAnet which provides a robust bi-directional communication network allowing continued redundant operation even during single point wiring failures. VESDAnet enables primary reporting, centralized configuration, control, maintenance and monitoring.
Ethernet and Wi-Fi Connectivity
VESDA-E detectors offer Ethernet and Wi-Fi connectivity as standard features. The detector can be added to a corporate network, allowing Wi-Fi enabled tablet devices and laptops installed with Xtralis configuration software to connect wirelessly to the detector via the network.
VESDA-E detectors occupy the same mounting footprint, pipe, conduit and electrical connector positioning as VESDA VLP and VLS detectors hence providing complete backwards compatibility.
How it Works
Air is continually drawn from the protected area through the air sampling pipe network and into the detector by a high efficiency aspirator. The air sampling pipe network can contain up to four pipes. The air from each sampling pipe passes through an airflow sensor and then a sample of the air is drawn into the smoke detection chamber via the sampling module, after first passing through the filter. An additional filter provides clean air to protect the optical surfaces inside the detection chamber from contamination.
The Flair™ detection chamber uses the equivalent of 330,000 sensors and sophisticated algorithms for detection and particle classification.
If the detected smoke is higher than the set alarm thresholds it is reported as an Alert, Action, Fire 1 or Fire 2 alarm condition.
Air is exhausted from the detector and may be vented back into the protected area.
Alarms can be signalled via Relays and VESDAnet. Ethernet and Wi-Fi can be used for configuration and secondary monitoring, and a USB interface is provided for initial setup.
A series of LEDs display Alarm, Trouble, Disable and detector power on status. A button allows the user to Reset or Disable the detector. In addition, an optional 3.5” LCD displays detector status including smoke level and a smoke level bar graph, alarm thresholds, trouble status, % airflow level, normalization status and filter life used.
- Ultra-wide sensitivity range
- Flow fault thresholds configurable per port
- Long-life, easy-to-replace filter
- Quiet operation
- LEDs for alarm and fault signalling
- 3.5” colour touch screen for status review
- Advanced remote diagnostics
- Area coverage up to 2,000 m² (21,500 ft²)
- Up to four inlet pipes
- Total pipe length of 800m (2,624ft)
- AutoLearn™ Smoke and Flow
- Seven programmable relays
- Two GPIs, monitored and unmonitored
- Ultrasonic flow sensing
- Xtralis VSC, VSM4 and ASPIRE-E PC software support
- IP40 Enclosure (not UL tested)
- Easy mounting with optional steel support bracket
- Field replaceable aspirator, sampling module, filter and detection chamber
- VESDAnet Networking
Ethernet 100 base T
- Wi-Fi, 802.11 b/g/n
- Local host-mode USB port
- Easy cable termination access
- Event Log (20,000 events)
The VESDA-E VEU is fully approved by VdS for safe use and installation in any European Union country and bears the CE mark to show that it complies with all the applicable Directives including the CPR, EMC and the Low Voltage Directive (LVD).
- EN54-20:2006 + AC:2008 – Fire detection and fire alarm systems – Control and indicating equipment.
|Supply Voltage||18-30 Vdc (24V Nominal)|
|Power Consumption @ 24Vdc||Aspirator Setting|
VEU-A00 & VEU-A10: 1-10
VEU-A00: 7.0w – 14.7w
VEU-A10: 8.2w – 15.8w
Power (In Alarm)
VEU-A00: 7.8w – 15.5w
VEU-A10: 10.4w – 16.6w
|Dimensions (W x H x D)||350mm x 225mm x 135mm (13.8in x 8.9in x 5.3in)|
|Weight||VEU-A00: 4.83kg (10.6 lbs)|
VEU-A10: 4.9kg (10.8 lbs)
|Operating Conditions||Ambient: 0°C to 39°C (32°F to 102°F)|
Sampled Air: -20°C to 60°C (-4°F to 140°F)
Tested to: -20°C to 55°C (-4°F to 131°F), UL: -20°C to 50°C (-4°F to 122°F)
Humidity: 10% to 95% RH, non-condensing
|Area Coverage||EN54-20: 2,000m2 (21,520 sq.ft)|
Up to 6,500 m² (69,965 sq.ft) System design and regulatory requirements may restrict the monitoring area to a lesser amount.
|Minimum airflow per pipe||15 l/m|
|Pipe lengths depending on number of pipes in use||1 Pipe: 160m (524ft)|
2 Pipe: 150m (492ft)
3 Pipes: 130m (426ft)
4 Pipes: 100m (328ft)
|Maximum Pipe Lengths||With branches: 800m (2624 ft)|
|Number of Holes||Class A: 80|
Class B: 80
Class C: 100
|Computer Design Tool||ASPIRE|
|Pipe||Inlet: External diameter 25mm or 1.05in (3/4in IPS)|
Exhaust: External diameter 25mm or 1.05in (3/4in IPS) via adaptor
|Relays||7 programmable relays (latching or non-latching states)|
Contacts rated 2A @ 30Vdc (Resistive)
|Cable Access||4 x 26mm (1.02in) cable entries|
|Cable Termination||Screw terminal blocks 0.2–2.5sq mm (24–14 AWG)|
|Dynamic Range||0.0002%/m (0.00006% obs/ft) to 20% obs/m (6.25% obs/ft)|
|Sensitivity Range||0.001% – 20.0% obs/m (0.0003 to 6.25% obs/ft)|
|Threshold Setting Range||Alert: 0.001%-2.0% obs/m (0.0003%-0.625% obs/ft)|
Action: 0.001%-2.0% obs/m (0.0003%-0.625% obs/ft)
Fire1: 0.001%-2.0% obs/m (0.0003%-0.625% obs/ft)
Fire2: 0.001%-20.0% obs/m (0.0003%-6.25% obs/ft)
|Software Features||Event log: Up to 20,000 events|
Smoke level, user actions, alarms and faults with time and date stamp
AutoLearn: Detector learns Alarm Thresholds and Flow Fault thresholds by monitoring the environment
Eurofyre are an authorised distributor of Xtralis (Honeywell) and have been a major technical wholesaler since 2007. We offer expert advice and supply all aspects of VESDA aspirating smoke detection systems including pipework calculations, demonstration/training and excellent after-sale support.
Contact us to receive competitive trade discounts or apply online for a credit account.