Key Features

  • EN54-20 approved
  • Dual pipe air-sampling
  • Single zone
  • Area coverage up to 2000m2
  • 0.001% to 20% obscuration/m

Overview

The Xtralis ICAM IFT-P Aspirating Smoke Detector is a very early warning smoke detector that can reliably detect fire during its early stages. ICAM IFT-P detectors have a sensitivity range from 0.001% to 20% obscuration/m (0.0003% to 6.10% obscuration/ft) and can detect low to high concentrations of smoke over an area of up to 2000 m2 (21 500 ft2).

Xtralis ICAM IFT-P detectors can be configured to suit an assortment of different environments and can provide reliable and accurate smoke detection for heavy industrial applications such as factories, chemical plants, mining facilities and warehouses as well as telecommunications and IT facilities.

How It Works

IFT-P detectors use powerful aspirators to draw air through sampling holes in an aspirating pipe network. The air is then filtered before being analysed in the detectors laser detection chamber.

The detectors aspirator is a 2000 Pa high volume and high-pressure fan. This provides superior detection times over long pipe lengths and reliable detection in high airflow environments. The airflow of each pipe is monitored by a dual element thermal sensing system. Airflow faults are indicated on the detector’s display and sent to monitoring equipment.

Four individually programmable alarm states (Alert, Action, Fire 1 and Fire 2) are shown using the detectors LED display, along with an OK/Fault indication. Dedicated output relays also provide interfaces for each alarm state and device fault.

Programming and Configuration

IFT-P detectors can be configured using Xtralis’ Configuration and Fire System Management software packages, Xtralis VSC and Xtralis VSM4, via RS232, RS485 and TCP/IP communication interfaces. The RS485 interface also allows connections to remote displays, and the TCP/IP Ethernet Interface can provide access to an email messaging service.

The IFT-P detector supports a maximum of three optional modules, which provide the detector with additional programmable output relay interfaces, and 4 to 20 mA analogue outputs.

Approvals

The ICAM IFT-P is fully approved by VdS and LPCB for safe use and installation in any European Union country and bears the CE mark to show that it complies with all the applicable Directives including the CPR, EMC and the Low Voltage Directive (LVD).

EN54-20:2006 + AC:2008 – Fire detection and fire alarm systems – Control and indicating equipment.

Tech Specs

Supply VoltageNominal 24Vdc
Supply Current500mA (min) to 1.2A (max)
Capacitive LoadingNominal 5,000 uF
Aspirator2000Pa Centrifugal air pump
Dimensions (W x H x D)254mm x 180mm x 165mm (10.0in. x 7.1in. x 6.5in)
Operating ConditionsAmbient: 0 to 39°C (32 to 103°F) UL Listed Detector Installed Ambient conditions
0°C to 38°C (32°F to 100°F)
Tested to: -10 to 55°C (14 to 131°F)
Sampled Air: -20 to 60 °C (-4 to 140°F)
Humidity: 10 to 95% RH (non-condensing)
Sampling Pipe SizeOuter Diameter:
25 mm, or; 1.05 in (3/4” pipe) with adaptor
Sampling HolesEN54-20:
Class A (12 holes / 0.04% obs/m)
Class B (36 holes / 0.04% obs/m)
Class C (36 holes / 0.1% obs/m)
Sampling NetworkZones: 1 Fire detection zone
Pipe Length: 2 x 100m (2 x 328ft)
Alarm Sensitivity Range0.001% to 20% obs/m (0.0003% to 6.10% obs/ft)
Alarm SettingsAlarm levels: Alert, Action, Fire 1 and Fire 2
Alarm delays: 0 to 60 seconds
Individually programmable for each level
IP RatingIP65
FiltrationField exchangeable dual stage filter
Flow MonitoringTwin thermal element
Relay Outputs4 alarm relays, 1 fault relay, 1 Amp changeover
Rating 1A @ 30Vdc, NO/NC
CommunicationRS232, RS485 Modbus
Ethernet TCP/IP
Event LogUp to 20,000 events stored

Downloads

Buy

2 Pipe, 1 Area Aspirating Smoke Detector

IFT-P
POA
Contact Us